|
|
 东芝168代码 |
|
|
| |
东芝168代码
December 2000 © TOSHIBA TEC 1 - 5 1600/2000/2500 ADJUSTMENT ITEMS
Classification Error code Machine status
CALL SERVICE from others
CALL SERVICE from laser
optical system
CALL SERVICE from finisher
(DP2000/2500 series)
Reserved
Scanner I/F
FAX unit
Offset catch tray
Reserved
C90 to C94 Reserved
C95 Power supply unit fan motor disconnection
C96 Process unit fan motor disconnection
C97 Vacuum fan motor disconnection
C98 Timer IC does not work normal
C99 PFC microcomputer abnormal
CA1 Polygon motor abnormal
CA2 HSYNC abnormal
CA3 to CB0 Reserved
CB1 Reserved
CB2 Exit motor abnormal
CB3 Reserved
CB4 Reserved
CB5 Staple motor abnormal
CB6 to CC2 Reserved
CC3 Set processing motor abnormal
CC4 to CC7 Reserved
CC8 Front aligning motor abnormal
CC9 Upper tray elevator motor abnormal
CCA Lower tray elevator motor abnormal
CCB Rear aligning motor abnormal
CCC to CD0 Reserved
F01 to F10 Reserved
F11 Scanner I/F error
F12 Write error at downloading the scanner unit program
F13 Download sector error of the scanner unit program
F14 Scanner unit F-ROM error
F15 to F20 Reserved
F31 Modem IC does not work normal
F32 to F40 Reserved
F41 Initial detection error of the offset catch tray
F42 to F99 Reserved1600/2000/2500 ADJUSTMENT ITEMS 1 - 4 December 2000 © TOSHIBA TEC
Classification Error code Machine status
CALL SERVICE from the
optical system
CALL SERVICE from the
process system
CALL SERVICE from fuser
area
CALL SERVICE from commu-nication
CALL SERVICE from ADF or
RADF
C21 Carriage initialization error
C22 to C24 Reserved
C25 Scanner unit watch dog error
C26 Exposure lamp disconnection or peak detection error
C27 to C30 Reserved
C31 to C37 Reserved
C38 Replaced process unit error
C39 to C40 Reserved
C41 Abnormal thermistor or heater disconnection at power ON
C42 Reserved
C43 Warming up mode after disconnection judgment, or abnor-mal
thermistor after ready
C44 Warming up mode after disconnection judgment, or heater
abnormal after ready
C45 Thermistor disconnection at the end part of heater
C46 to C50 Reserved
C51 to C55 Reserved
C56 Communication error between PFC and main unit
C57 Communication error between main unit and IPC (DP2000/
2500 series)
C58 Communication error between IPC and finisher (DP2000/
2500 series)
C59 to C70 Reserved
C71 Paper supply motor lock error
C72 Reserved
C73 EE-PROM initialization error
C74 Defective adjustment by the exit/reversal sensor detected
C75 to C80 Reserved
C81 Fan motor lock error
C82 Document aligning lower sensor (RADF)/Aligning sensor
(ADF) adjustment error
C83 Size length adjustment error
C84 to C89 ReservedDecember 2000 © TOSHIBA TEC 1 - 3 1600/2000/2500 ADJUSTMENT ITEMS
- Internal tray full (when finisher bridge installed) (DP2000/
2500 series)
- No paper in the cassette 1
- No paper in the cassette 2
- No paper in the cassette 3
- No paper in the cassette 4 (DP2000/2500 series)
- No paper in the LCF (DP2000/2500 series)
- Cassette 1 is not ready
- Cassette 2 is not ready
- Cassette 3 is not ready
- Cassette 4 is not ready (DP2000/2500 series)
- LCF is not installed (DP2000/2500 series)
Front cover or side cover of the copier is open
Cover of the job separator is open
Cover of the off set catch tray is open
Cover of the bridge cover is open (DP2000/2500 series)
Cover of the ADU is open
Side cover of the cassette 2 is open
Side cover of the cassette 3 is open
Side cover of the LCF is open (DP2000/2500 series)
Finisher joint is open (DP2000/2500 series)
No staples (displayed only when stapling is designated)
(DP2000/2500 series)
C01 Main motor drive error
C02 to C03 Reserved
C04 PFP main motor drive error
C05 Reserved
C06 LCF feed motor error (DP2000/2500 series)
C07 to C10 Reserved
C11 to C12 Reserved
C13 Cassette 1 error
C14 Cassette 2 error
C15 Cassette 3 error
C16 Cassette 4 error (DP2000/2500 series)
C17 Reserved
C18 LCF tray error (DP2000/2500 series)
C19 LCF feed motor abnormal (DP2000/2500 series)
C20 Reserved
Classification Error code Machine status
Other operator calls
CALL SERVICE from drive
system
Temporary paper supply
mechanism error1600/2000/2500 ADJUSTMENT ITEMS 1 - 6 December 2000 © TOSHIBA TEC
1.2 Self-Diagnosis Modes
The self-diagnosis functions are used to make the settings for the various PPC functions. This document
describes the self-diagnosis functions.
For the FAX functions, refer to the SERVICE HANDBOOK (GD-1060).
For the method to enter each mode of the self-diagnosis functions, refer to the following chart.
*1: After inputting the country code, the copier automatically enters the warm up mode.
*2: After the RAM clear, the machine automatically enters the warm up mode.
*3: In the SERVICE MODE, each function of the FUNCTION TEST, MAINTENANCE, or SERVICE LIST
in each test item of the TEST MODE (displayed by pressing the PROGRAM key), are added. When
the copier enters this mode, these functions are available.
Definition
Selects the country code.
Finely adjusts copy image quality.
Confirmation printing enabled by
pressing the INTERRUPT key.
Performs setups for the system,
maintenance, operations, printer,
scanner, etc.
Fixes the scanner carriage in place
when transporting the copier.
Clears values excluding the ones
set in 08-446/447 and in the Ad-just
mode (05).
Performs setups for FUNCTION
TEST and MAINTENANCE, and
prints the Service List.
Conducts OPE. PANEL TEST,
PRINT TEST, MODEM TEST, etc.
Performs setups for Memory Clear,
facsimile function, etc.
Prints PROTOCOL TRACE, Total
Error, FUNCTION LIST, etc.
Mode
Country code
Adjust mode
System mode
Scanner parking
mode
RAM clear
Service mode
*3
FUNCTION
TEST
MAINTENANCE
Service list
How to clear
*1
Turn the power off.
Turn the power off.
Turn the power off.
*2
Press the
PROGRAM key,
and then press the
*, #, *, then * keys.
Or turn the power
off.
Or press the
COPY key, or
press the MAIN
MENU key.
How to enter
Turn the power on while
pressing the 0 and 2 keys.
Turn the power on while
pressing the 0 and 5 keys.
Turn the power on while
pressing the 0 and 8 keys.
Turn the power on while
pressing the 0 and 9 keys.
Turn the power on while
pressing the 1, 3, and * keys.
Press the PROGRAM key
while REDAY is indicated,
and then press the *, #, *,
then * keys.
After entering the service
mode, select it on the screen.
This mode is selected by
turning the power on while
pressing the 1 and 3 keys.
After entering Service Mode,
select it on the screen.
After entering Service Mode,
select it on the screen. |
|
|
| 发布日期：2019/11/24 |
| 宜昌打印机维修 复印机 一体机上门维修热线：13677173728 邢师傅 0717-6736581 |
|
